Neofil F7 High Performance Water Resistant Ceramic Tile Adhesive for Internal Applications
In stock
A premixed cement based ceramic tile adhesive. It is composed of grey or white colour powder and does not contain asbestos nor any other harmful components.
Colors: Available in Grey
Packaging:
NEOFIL F7 is packed in 25 Kg bags.
ر.س 2.50 excl. Tax
Neofil F7 High Performance Water Resistant Ceramic Tile Adhesive for Internal Applications
![](https://nabni.com/wp-content/uploads/2021/10/Neofil-F7-1-768x835.png)
A premixed cement based ceramic tile adhesive. It is composed of grey or white colour powder and does not contain asbestos nor any other harmful components.
USES
NEOFIL F7 is used for the permanent fixing of ceramic tiles for internal applications. It may be suitable for use in:
-
- Kitchens
- Bathrooms
- Regular rooms
ADVANTAGES
- High bond strength
- Water resistant
- Economical
- Eco-friendly
- Tropical grade
- Formulated to suit Middle East conditions
INSTRUCTIONS FOR USE
Surface preparation
All surfaces should be sound, clean & uncontaminated. This preparation should leave an exposed concrete surface free from dust, loose particles, deletrious matter, oil, grease, chemical films & other contaminant.
All loose particles of mortar, paint, etc. must be physically removed.
Concrete or blockwork: Allow to cure sufficiently so that all shrinkage movements take place before fixing tiles.
Gypsum supports: Treat with PRIMER A16. Should not have a percentage of humidity more than 10%.
The surface of substrates must be moistened slightly with clean water to reduce the absorption of water from the mortar.
Do not moistened the tiles.
Mixing
Place 5.0 – 5.25 liters of cold, potable water (or ELASTOKOL as needed) in the mixing bucket and add slowly 25 kg bag of NEOFIL F7 under continuous mixing till a uniform lump free consistency mix is achieved. For mixing process, a slow speed drill (200-300rpm) fitted with a suitable paddle is recommended.
Allow the obtained mix to stand for about 5 minutes and then remix before application.
Application
Spread NEOFIL F7 on the substrate to a uniform thickness using a toothed spatula, the first pass with its straight edge and the second pass immediately after, to the desired thickness of NEOFIL F7 using the toothed part.
Place the tiles onto the adhesive bed. Apply sufficient pressure on the tile during fixing with slight twisting movement in order to ensure good contact with the adhesive.
In case of large size tiles, it is necessary to spread the adhesive also to the backside of the tile and then place the tiles into the adhesive bed.
Apply enough material that can be tiled during the adhesive’s open wet time. Spreading large areas may result in drying the adhesive before tiles can be fixed causing poor adhesion.
Finishing
Remove excess adhesive with a damp cloth before it dries. Joints grouting between tiles may be commenced after 10 hours of tiling for walls and 24 hours for floors.
Cleaning
Tools and equipment should be cleaned with water immediately after use. Hardened materials should be mechanically removed.
Recommendations
- To achieve improved adhesion strength, it is recommended to replace water with ELASTOKOL.
- The grey type presents higher mechanical resistances. It is therefore advisable to use to fix tiles on floor.
- Stiffened mortar must neither be diluted with water nor with fresh mortar.
- Do not use NEOFIL F7 on metal or non-absorbing surfaces.
- Do not apply NEOFIL F7 in rainy weather, high winds and sand storms.
- Do not apply under direct sun.
- Keep equipment cool and use cold water.
- Porosity of tiles and substrates has significant effect on adhesive strength of tile.
-
Plaster Mix M Designed for Manual Plastering For Areas Not Accessed By Machine Applications
Sold By: The White Blocksر.س 1.60 excl. TaxSold By: The White BlocksPlaster Mix M Designed for Manual Plastering For Areas Not Accessed By Machine Applications
ر.س 1.60 excl. Tax -
ر.س 4.00 excl. TaxSold By: The White Blocks
Vetorep CR520 High Strength Ready to Use Structural Repair Mortar
ر.س 4.00 excl. Tax
-
ر.س 3.00 excl. Tax
-
ر.س 75.00 excl. Tax
-
ر.س 0.18 excl. Tax
-
ر.س 0.10 excl. Tax
-
ر.س 0.15 excl. Tax
-
ر.س 0.10 excl. Tax
-
ر.س 0.33 excl. Tax
-
ر.س 35.00 excl. TaxSold By: Muna Noor
1.5 Inch Pelican Rain Gun Irrigation Sprinkler, Model No.: HT-42G
ر.س 35.00 excl. Tax -
ر.س 14.00 excl. Tax
Reviews
There are no reviews yet.